Pedestal bearings – EG / ER type

Pedestal bearing housings, i.e., housings intended to be positioned on foundation constructions, are widely used in general mechanical engineering applications. The housings up to size 45 are designed with finned surfaces to allow for the best possible dissipation of heat to the surrounding air. Self-cooling bearing designs are still feasible for numerous applications in this size range. Sizes 18 to 45 are available with either a finned or smooth surface, and with smooth surfaces only from size 56 and up. The simpler, smooth design is always sufficient when the lubricant is cooled externally (external lubrication systems). The type ID for smooth pedestal bearing housings is EG, and ER for the finned version. The shaft heights of the pedestal bearings are selected such that the housing can be easily located at the shaft heights of the machines using foot plates or consoles. When the bearing shells and seals are dismantled, the housings can be slid in the axial direction without removing the rotor. If the housings are standing on intermediate pedestals (consoles), they can be lowered and pulled away to the side once the consoles have been removed. The foundations should be constructed with a sufficient level of rigidity to ensure that the machines operate smoothly and reliably.


Pedestal bearings – EG / ER type

Slide bearings have lower noise levels in comparison to rolling bearings and are resistant to loads caused by shocks thanks to lower material stresses

Slide bearings are maintenance-free or low-maintenance and easy to install

Slide bearings have a lubricant film that dampens vibrations, impacts, and noise

Slide bearings are resistant to dust penetration and shocks

Slide bearings require a small radial installation space and are structurally adaptable (can be integrated as component)

Slide bearings are suitable for very high speeds

Slide bearings exhibit practically no wear during fully hydrodynamic continuous operation and with hydrostatic bearings

Slide bearings are most cost-effective than rolling bearings at large dimensions

Technical data

EG bearing
Unfinned pedestal bearing acc. to DIN 31690 / ISO 11687-1
18 … 28, for shafts Ø 160 … 355 mm
35 … 112, for shafts Ø 300 … 1,250 mm
ER bearing
Finned pedestal bearing acc. to DIN 31690 / ISO 11687-1
9 … 28, for shafts Ø 55 … 355 mm
35 … 45, for shafts Ø 300 … 560 mm
Self-lubricating (loose oil ring, fixed oil ring) or external lubrication
Cooling system:
Natural cooling, water cooling, or external cooling
Bore design:
Various bore designs as required, e.g. cylindrical bore, two-lobe bore, four-lobe bore, or radial tilting pad
Electric insulation, lubricant circulation system, hydrostatic jacking
Temperature monitoring with PT100, prepped for vibration/speed sensors


Other products

Online Store

In our online store we offer selected spare parts for our E-bearings and our ELCO couplings.

To the online store

Slide bearings, EF type

The EF design is especially suitable for electrical machines which do not have their own bearing foundations or the alignment work that goes with them, because they enable significantly shorter bearing clearances and therefore more rigid rotor constructions in comparison to pedestal bearings.

Go to product

Slide bearings, EM type

Slide bearings of the the EM type make it possible to provide very large access areas to the interior of the machine and the bearings for installation purposes – an extraordinary advantage when assembling the machine and performing maintenance work. This housing shape serves as a very suitable basis for a wide range of expansion stages in demanding drive concepts in particular.

Go to product

Relevant industries


Shipping industry

Gear units, slide bearings, and couplings for the shipping industry. Make the most of reliable, low-emission drive technology from RENK.

Go to industry


Oil and gas

Turbines, pumps, and compressors for the oil and gas industry; boost your productivity.

Go to industry


Energy production

Turbo gear units, couplings, and slide bearings for the field of energy production. RENK drive technology guarantees high system availability at all times.

Go to industry


Steel and metal

Components for rollers, roller conveyors, or reel drives for the steel industry: we find the perfect solution for you.

Go to industry

Your contact person